#Homeseer switch install#
#Homeseer switch update#
#Homeseer switch upgrade#

|В If a controller goes into NWI exclusion mode, HSM200 could be excludedВ without pressing the button. |В LearnMode was left enabled after the button was pressed in previous revisions. This shorter timeout makes itВ possible to use OnTime=0 mode more effectively. |В The minimum timeout for sending a motion notification when OnTime is set to 0В has been reduced from 1 minute to 10 seconds. Note that Rev H only has luminance in percent. Rev H is 0x01.В For Rev H boards, the luminance sensor always returned 0 in Rev 1.7. The Version Report command (V2) now replies with a Hardware Version of 0x02 forВ on RevJ hardware and later. V1.8:В Add Hardware version to Version report command The odd minor revs are reserved for branches. |В FCC testing mode has changed to support 5 different modes. They are rare but frequent enough it was decided to put additional checkingВ in to reboot if there are more than 10 frame delivery failures in a row or ifВ it has been more than 18 hours since the last communication. Reports of nodes requiring a power cycle to get them to talk again were comingВ in.

#Homeseer switch upgrade#

v1.10: SDK upgrade and reboot if no communication in 18hrs.

|В Multilevel Switch doesnвЂ™t dim the LED, it only turns it on/off. | Multilevel Switch command class wasВ added as required for support of the Color Command class for the color LED. |В Configuration Command Class upgraded to V3 so the parameter names and information can be obtained directly from the device without the need for custom programming. Initial release using Sigma SDK 6.81.00 which adds security S2 and SmartStart.

v2.1: Upgrade to SmartStart вЂ“ Z-Wave Certification rev.

|В Various other small changes were required to pass certification but would notВ impact typical users. This is aВ change in the certification and the sensor MUST always send a sensor reading.

|В The parameter value of 0 is no longer valid for the sensor readings. ZWave Library 6.81.00 вЂ“ ONLY FOR UNITS WITH SCREW TAB!ДЄdded the Supervision Command Class to the non-secure NIF.

#Homeseer switch update#

| To get the settings for the changes, please update to the latest Beta of the Z-Wave plugin 3.0.1.234 or later. Note that a central scene command for single taps IS still sent. When disabled, the load will respond instantly to paddle presses. | Ability to disable the multi-tap feature on both WS and WD. This allows other WX200 devices to used as companion switches. Any device added to group 2 will be controlled. v5.12: Added a parameter to allow for lower dimming on the WD200.This ensures that both dimmers LEDS stay in sync. v5.13: В When using group 2 association the controlling dimmer will send a BASIC SET to the associated dimmer after it reaches the desired dim level.

#Homeseer switch install#

If you install it on any other device, it may render that device inoperable. If it fails, do a connectivity check, then remove.Д¬areful: Be sure to install this dimmer firmware on the HS-WD200+ dimmer. After adding the switch back in, click on the old device then Z-Wave tab, then вЂњRemove Bad NodeвЂќ to remove the node from the Z-Wave interface. You will need to add the switch back into your network. This was an unfortunate consequence of adding the group 2 association feature. Note: When updating to this firmware the node ID of the switch will be lost.

v5.14: Fixed multiple taps controlling the load (multiple taps should not control the load) | Modified parameter 5 to specify the lowest dim level the dimmer will provide (6.5% -> 20%) (Values are 1-14) | Z-Wave plugin version 3.0.1.249 required in order to set the lowest dim level parameter from the device Z-Wave settings.